WilsonCellbanner.gif
Authorized Dealer

 
 
LET US HELP YOU DESIGN YOUR SYSTEM
 
 
Home and Office installation services are available in the Atlanta area

Wilson Amplifiers and Repeaters
 
The Wilson products for signal enhancement continue to expand our communications horizon.  Where once we had to wait until we moved into range of a cell tower, we can now bring that signal to where it is needed.  Homes, offices, condos, and RVs (land or marine/fixed or mobile) can all benefit from the signal amplifiers and repeaters from Wilson.
 
 

Direct Connect Amplifiers
 
The direct-connect (wired) nature of an amplifier requires that it be connected to an external antenna on one end and a cellular device on the other end.  While being limited by the length of the cable can be a problem, some situations adapt very well to this design...and it is cost effective.

Wilson Direct-Connect Cellular Amplifier
Wilson Direct-Connect Cellular Amplifier
Click for Larger Picture

Wilson #811201 Direct Connect Amplifier
Wilson #811201 Direct Connect Amplifier

#811201 Bi-Directional Dual Band Amplifier
 
This unit will amplify both the low (Cellular) and the high (PCS) bands for all carriers except iDEN (NEXTEL, Southern Linc).  Cell phones and wireless laptop modems will benefit from this amplifier.  This unit works well in most any situation (fixed or mobile) allowing a direct connection between the amplifier and the cellular device.

Wilson #814001 iDEN/NEXTEL Amplifier  Direct-Connect Cellular Signal Booster
Wilson #814001 iDEN/NEXTEL Amplifier

 
 
 
 
#814001 iDEN Amplifier...
 
Good for any application from vehicles to construction trailers.  This direct connect amplifier will allow you to stay in touch with your crew.

 
 
 
Typical Installation 'Kit'
Wilson Electronics does not market "Kits" for their repeaters and amplifiers.  However, to make things easier for you, OmniCell will provide you with an 'installation kit'.  Most 'kits' come with an established set of components.  To vary from those components mean extra cost.  Not true with our Wilson products.  We will work with you to be certain that everything is the type and length that is necessary to give you the results you need.
 
The 'kit' below lists the most common components for a typical fixed-location installation of the direct-connect system.  If your needs differ, we will be sure that your kit contains only those components that work for you.
  • Omni-Directional Exterior Antenna  (Wilson #301101 Trucker Antenna)
  • 30 feet Low Loss Coax Cable with connectors
  • Dual-Band In-Line Amplifier  (Wilson #811201 3-Watt amp)
  • 5 feet Low Loss Coax Jumper with connectors
  • Cellular Device Antenna Adapter Cable (Device specific)

Your price for the above kit...$559.00

 
 
 
 
 
 
 
Wireless (no connection) Repeaters
 
The repeater allows multiple cellular devices to be used at one time.  After amplifying the signal received from the exterior antenna, the signal is 'repeated' through the attached internal antenna.  Although the true coverage area depends upon the strength of the signal received at the exterior antenna, the indoor signal may penetrate into adjoining rooms and floors.
 
Wilson has introduced its dual-band repeater for a fixed location to compliment its successful mobile dual-band repeater.  Single band units will remain a standard for large coverage areas and commercial installations.

Wilson Wireless Repeaters are an excellent choice to enhance the cell signal in any situation.
Wilson Wireless Cellular Repeaters

Wilson #801105 50dB 800 MHz Repeater will out-perform most other repeaters.  Also available in 60 dB model #801106.
Wilson #801105 50dB 800 MHz Repeater

#801105 50 dB in-Building Repeater...
 
The Cellular 50 dB Amplifier improves signals on the Cellular (824-894 MHz) band and works with Verizon, US Cellular, Cellular One, Alltel, Bell Canada, Telus, Cingular and all other 800 MHz Cellular carriers.  This equipment will not provide a signal for the iDEN network (NEXTEL, etc.)

80110550dB800MHz.jpg

#801245 SOHO Cellular/PCS Dual Band Repeater...
Now in Stock!
This new repeater from Wilson will allow you to design your own in-building installation around a single unit.  The repeater will boost the low frequency by approximately 40 dB and the high frequency by 50 dB.

Wilson #804005 iDEN/NEXTEL Wireless Repeater
Wilson #804005 iDEN/NEXTEL Wireless Repeater

#804005 iDEN Repeater...
 
This unit will amplify and repeat the signals of NEXTEL, Southern Linc, and other iDEN carriers.  This unit should not be used when the 800 MHz Cellular frequency is also amplified. 

 
 
 
 
Typical Installation 'Kit'
Generally, a 'kit' does not allow for changes in its configuration.  That is why Wilson does not market a system kit.  However, to make things easier for you, OmniCell will provide you with an 'installation kit'.  We will work with you to be certain that everything in your kit is the type and length that is necessary to give you the results you need.
 
The 'kit' below lists the most common components for a typical fixed-location installation of a wireless repeater system.  If your needs differ, we will be sure that your kit contains only those components that work for you.  Note that the entrance cable is longer for the repeater system than the direct-connect system.  That is to allow for the minimum distance between the two antennas.  Since both antennas will be transmitting and receiving, there is an opportunity for feedback and oscillation if the antennas do not have sufficient distance between them.
  • Omni-Directional Exterior Antenna  (Wilson #301101 Trucker Antenna)
  • 40 feet Low Loss Coax Cable with connectors
  • Dual-Band Repeater (Wilson #801245)
  • 'Rubber Duck' 6" flexible antenna

Your price for the above kit...$675.00